Hentie's scores

[tburke]

Good luck for the weekend's session! I will list your 30s metal score of 5616 on the thread. I guess it's right handed?

[Hentie]

Thats great. good luck for the weekend.

Thank you!

That's good news! Good luck for weekend session!

Thank you!

Good luck for the weekend's session! I will list your 30s metal score of 5616 on the thread. I guess it's right handed?

Yes, it was right-hand. Thanks!

[Hentie]

I done a small wearing-in session with my new rotor just to taste if it will be promising... I don't know! I battled even to get 14.5k with it. Just slips and battles to ''bite'' wel! A new ball will be perfect but that is out of the question. Hitting 16k was really a big jump for me and I am still very proud of it!

[Mika Mäkinen]

Are you sure that axle and surface on the cell is perfectly clean? If you mount washers and support ring with bare hands i bet there are some grease from your fingers. I use pincers to put washers on their place and carefully put support ring without touching axle. Maby i'm too precise with it, but i like to be sure.
Try to clean axle and surfaces with alcohol or isopropanol maby it helps.

My opinion is that everyone who has conquer 16k should have free balls from manufacturer for life!

[LTLFTC]

I done a small wearing-in session with my new rotor just to taste if it will be promising... I don't know! I battled even to get 14.5k with it. Just slips and battles to ''bite'' wel! A new ball will be perfect but that is out of the question. Hitting 16k was really a big jump for me and I am still very proud of it!

When I clean a ball it will always drop my 15k went down about 800 rpm but took about an hour and it was back in the swing

[Hentie]

Thank you, guys! When I open my auto-start it seems like it scratches(or "bites") into the black cavity ring which releases small flakes then I have to lightly sand it smooth. But it seems to "bite" better when I have lightly sanded the bottom shell but it doesn't last till it starts slipping again!?

[bman]

I normally put the ball in to first mode and spin until I get it to 500 then try speed, good luck I will need you to keep pushing me

[Hentie]

Ok, I have sorted the problem with my auto-start. The cavity ring surface needed some propper sanding and the inside edges needed some rounding!
I had a session last night which I will post soon.

[Hentie]

For some reason I am going through a set back stage... after peacking so wel.. It feels like I just lost my strength!(Anyone ever had it?) (I must also admit that I am goining through a stressful time at the moment.)
I decided to have a training session with a pro-amber, metal and auto to see how I will do?
Here are the scores as follows:

Pro Amber: 5967R, 6065L, 13962R, 13134L, 6366R, 6351L, 14004R, 13820L, 6058R, 6310L.
Metal(Speed only): 12205R, 11430L, 12520R, 11800L, 12862R, 11922L, 12534R, 11986L, 12690R.
Auto-start: 14188R, 14004L, 14596R, 14512L, 14482R, 14220L, 6729R, 6762L, 14689R, 14303L, 14777R, 14929R, 15004R, 15186R.

I have made turns with each ball starting with the pro-amber. There are a few scores in between that I haven't recorded here!
Conclusion:
I have and can do much better with the pro-amber.
My metal scores are at least progressing closser to 13k again.
My auto-start scores only started touching 15k after a 30s endurance and that was at the end of my session.
I must say that my left-hand seem to be in good shape has been able to hit 14.5k again!

Will see what the next session will be! Sorry Ben, not much compitition for you at the moment!

[Jaco Snyman]

After a long break I have had the same experience of not hitting the scores I want. Do anohter session today or tomorrow and you will notice that the scores will increase again. I have found If I had a long break that my endurance scores go up but not my speed so much. Nice left had score.

Good luck with your next session. And dont lose interest now. now is the time you have to keep on training. This is the time when I lost interest. got a nice high score and did not break it for a long time and thought thats it.

Keep them spinning.